mixmstrs

mixmstrs · utilities

8xstereo mixer with EQ, per-channel compressor (single-dial macro + power-user thresh/ratio), two stereo aux sends/returns, per-channel post-fader VU taps (read('levels') → number[8]). Multiple instances allowed. 81 params.

An 8-channel stereo mixer with a channel strip on every input — the master bus of a patch. Each of the eight channels takes a stereo pair, runs it through a 3-band EQ (low/mid/high, ±12 dB), an optional compressor, and a volume fader, then sums into the stereo MASTER output. Two stereo AUX SENDS tap each channel (per-channel SEND 1 / SEND 2 amounts) out to send1L/R and send2L/R — patch an external reverb/delay off a send and bring its wet signal back into the matching stereo RETURN, which sums into the master. The compressor is exposed two ways: manual THRESH / RATIO / ENABLE per channel, OR a single COMP macro knob that collapses all three into one 'amount' (0 = bypass, up to a moderate −20 dB / 4:1 at full). EVERY parameter also has a CV input (so an LFO can ride a fader, EQ band, or send), and the card shows a post-fader VU meter per channel. Multiple MIXMSTRS instances are allowed for submixes / parallel buses — each sums additively into its destination.

the faceplate

111 inputs · 6 outputs · 91 params

about this module

Hover a control, or open the patch panel and hover a jack.

inputs

id	cable	what it does
`ch1L`	audio	Channel 1 left audio input. Pairs with ch1R as the stereo source for mixer channel 1. audio signal; L/R stereo pair with ch1R — L-only auto-duplicates to R
`ch1R`	audio	Channel 1 right audio input, partnering ch1L. audio signal; L/R stereo pair with ch1L
`ch2L`	audio	Channel 2 left audio input. Pairs with ch2R as the stereo source for mixer channel 2. audio signal; L/R stereo pair with ch2R — L-only auto-duplicates to R
`ch2R`	audio	Channel 2 right audio input, partnering ch2L. audio signal; L/R stereo pair with ch2L
`ch3L`	audio	Channel 3 left audio input. Pairs with ch3R as the stereo source for mixer channel 3. audio signal; L/R stereo pair with ch3R — L-only auto-duplicates to R
`ch3R`	audio	Channel 3 right audio input, partnering ch3L. audio signal; L/R stereo pair with ch3L
`ch4L`	audio	Channel 4 left audio input. Pairs with ch4R as the stereo source for mixer channel 4. audio signal; L/R stereo pair with ch4R — L-only auto-duplicates to R
`ch4R`	audio	Channel 4 right audio input, partnering ch4L. audio signal; L/R stereo pair with ch4L
`ch5L`	audio	Channel 5 left audio input. Pairs with ch5R as the stereo source for mixer channel 5. audio signal; L/R stereo pair with ch5R — L-only auto-duplicates to R
`ch5R`	audio	Channel 5 right audio input, partnering ch5L. audio signal; L/R stereo pair with ch5L
`ch6L`	audio	Channel 6 left audio input. Pairs with ch6R as the stereo source for mixer channel 6. audio signal; L/R stereo pair with ch6R — L-only auto-duplicates to R
`ch6R`	audio	Channel 6 right audio input, partnering ch6L. audio signal; L/R stereo pair with ch6L
`ch7L`	audio	Channel 7 left audio input. Pairs with ch7R as the stereo source for mixer channel 7. audio signal; L/R stereo pair with ch7R — L-only auto-duplicates to R
`ch7R`	audio	Channel 7 right audio input, partnering ch7L. audio signal; L/R stereo pair with ch7L
`ch8L`	audio	Channel 8 left audio input. Pairs with ch8R as the stereo source for mixer channel 8. audio signal; L/R stereo pair with ch8R — L-only auto-duplicates to R
`ch8R`	audio	Channel 8 right audio input, partnering ch8L. audio signal; L/R stereo pair with ch8L
`ret1L`	audio	Aux RETURN 1 left input — the wet signal coming back from the effect on send 1; summed (stereo) into the master bus. audio signal; L/R stereo pair with ret1R — L-only auto-duplicates to R
`ret1R`	audio	Aux RETURN 1 right input, partnering ret1L. audio signal; L/R stereo pair with ret1L
`ret2L`	audio	Aux RETURN 2 left input — the wet return for send 2; summed into the master bus. audio signal; L/R stereo pair with ret2R — L-only auto-duplicates to R
`ret2R`	audio	Aux RETURN 2 right input, partnering ret2L. audio signal; L/R stereo pair with ret2L
`ch1_volume`	cv	CV that offsets channel 1's VOLUME fader (±1 CV sweeps the full 0..1 span around the knob). control voltage (CV); modulates ch1_volume (summed directly (the destination DSP scales it))
`ch1_low`	cv	CV that offsets channel 1's LOW EQ band. control voltage (CV); modulates ch1_low (summed directly (the destination DSP scales it))
`ch1_mid`	cv	CV that offsets channel 1's MID EQ band. control voltage (CV); modulates ch1_mid (summed directly (the destination DSP scales it))
`ch1_high`	cv	CV that offsets channel 1's HIGH EQ band. control voltage (CV); modulates ch1_high (summed directly (the destination DSP scales it))
`ch1_thresh`	cv	CV that offsets channel 1's compressor THRESHOLD. control voltage (CV); modulates ch1_thresh (summed directly (the destination DSP scales it))
`ch1_ratio`	cv	CV that offsets channel 1's compressor RATIO. control voltage (CV); modulates ch1_ratio (summed directly (the destination DSP scales it))
`ch1_compEnable`	cv	CV (discrete) that toggles channel 1's compressor ENABLE. control voltage (CV); modulates ch1_compEnable (summed directly (the destination DSP scales it))
`comp1`	cv	CV that offsets channel 1's COMP macro amount. control voltage (CV); modulates comp1 (summed directly (the destination DSP scales it))
`ch1_send1`	cv	CV that offsets channel 1's SEND 1 amount. control voltage (CV); modulates ch1_send1 (summed directly (the destination DSP scales it))
`ch1_send2`	cv	CV that offsets channel 1's SEND 2 amount. control voltage (CV); modulates ch1_send2 (summed directly (the destination DSP scales it))
`ch2_volume`	cv	CV that offsets channel 2's VOLUME fader (±1 CV sweeps the full 0..1 span around the knob). control voltage (CV); modulates ch2_volume (summed directly (the destination DSP scales it))
`ch2_low`	cv	CV that offsets channel 2's LOW EQ band. control voltage (CV); modulates ch2_low (summed directly (the destination DSP scales it))
`ch2_mid`	cv	CV that offsets channel 2's MID EQ band. control voltage (CV); modulates ch2_mid (summed directly (the destination DSP scales it))
`ch2_high`	cv	CV that offsets channel 2's HIGH EQ band. control voltage (CV); modulates ch2_high (summed directly (the destination DSP scales it))
`ch2_thresh`	cv	CV that offsets channel 2's compressor THRESHOLD. control voltage (CV); modulates ch2_thresh (summed directly (the destination DSP scales it))
`ch2_ratio`	cv	CV that offsets channel 2's compressor RATIO. control voltage (CV); modulates ch2_ratio (summed directly (the destination DSP scales it))
`ch2_compEnable`	cv	CV (discrete) that toggles channel 2's compressor ENABLE. control voltage (CV); modulates ch2_compEnable (summed directly (the destination DSP scales it))
`comp2`	cv	CV that offsets channel 2's COMP macro amount. control voltage (CV); modulates comp2 (summed directly (the destination DSP scales it))
`ch2_send1`	cv	CV that offsets channel 2's SEND 1 amount. control voltage (CV); modulates ch2_send1 (summed directly (the destination DSP scales it))
`ch2_send2`	cv	CV that offsets channel 2's SEND 2 amount. control voltage (CV); modulates ch2_send2 (summed directly (the destination DSP scales it))
`ch3_volume`	cv	CV that offsets channel 3's VOLUME fader (±1 CV sweeps the full 0..1 span around the knob). control voltage (CV); modulates ch3_volume (summed directly (the destination DSP scales it))
`ch3_low`	cv	CV that offsets channel 3's LOW EQ band. control voltage (CV); modulates ch3_low (summed directly (the destination DSP scales it))
`ch3_mid`	cv	CV that offsets channel 3's MID EQ band. control voltage (CV); modulates ch3_mid (summed directly (the destination DSP scales it))
`ch3_high`	cv	CV that offsets channel 3's HIGH EQ band. control voltage (CV); modulates ch3_high (summed directly (the destination DSP scales it))
`ch3_thresh`	cv	CV that offsets channel 3's compressor THRESHOLD. control voltage (CV); modulates ch3_thresh (summed directly (the destination DSP scales it))
`ch3_ratio`	cv	CV that offsets channel 3's compressor RATIO. control voltage (CV); modulates ch3_ratio (summed directly (the destination DSP scales it))
`ch3_compEnable`	cv	CV (discrete) that toggles channel 3's compressor ENABLE. control voltage (CV); modulates ch3_compEnable (summed directly (the destination DSP scales it))
`comp3`	cv	CV that offsets channel 3's COMP macro amount. control voltage (CV); modulates comp3 (summed directly (the destination DSP scales it))
`ch3_send1`	cv	CV that offsets channel 3's SEND 1 amount. control voltage (CV); modulates ch3_send1 (summed directly (the destination DSP scales it))
`ch3_send2`	cv	CV that offsets channel 3's SEND 2 amount. control voltage (CV); modulates ch3_send2 (summed directly (the destination DSP scales it))
`ch4_volume`	cv	CV that offsets channel 4's VOLUME fader (±1 CV sweeps the full 0..1 span around the knob). control voltage (CV); modulates ch4_volume (summed directly (the destination DSP scales it))
`ch4_low`	cv	CV that offsets channel 4's LOW EQ band. control voltage (CV); modulates ch4_low (summed directly (the destination DSP scales it))
`ch4_mid`	cv	CV that offsets channel 4's MID EQ band. control voltage (CV); modulates ch4_mid (summed directly (the destination DSP scales it))
`ch4_high`	cv	CV that offsets channel 4's HIGH EQ band. control voltage (CV); modulates ch4_high (summed directly (the destination DSP scales it))
`ch4_thresh`	cv	CV that offsets channel 4's compressor THRESHOLD. control voltage (CV); modulates ch4_thresh (summed directly (the destination DSP scales it))
`ch4_ratio`	cv	CV that offsets channel 4's compressor RATIO. control voltage (CV); modulates ch4_ratio (summed directly (the destination DSP scales it))
`ch4_compEnable`	cv	CV (discrete) that toggles channel 4's compressor ENABLE. control voltage (CV); modulates ch4_compEnable (summed directly (the destination DSP scales it))
`comp4`	cv	CV that offsets channel 4's COMP macro amount. control voltage (CV); modulates comp4 (summed directly (the destination DSP scales it))
`ch4_send1`	cv	CV that offsets channel 4's SEND 1 amount. control voltage (CV); modulates ch4_send1 (summed directly (the destination DSP scales it))
`ch4_send2`	cv	CV that offsets channel 4's SEND 2 amount. control voltage (CV); modulates ch4_send2 (summed directly (the destination DSP scales it))
`ch5_volume`	cv	CV that offsets channel 5's VOLUME fader (±1 CV sweeps the full 0..1 span around the knob). control voltage (CV); modulates ch5_volume (summed directly (the destination DSP scales it))
`ch5_low`	cv	CV that offsets channel 5's LOW EQ band. control voltage (CV); modulates ch5_low (summed directly (the destination DSP scales it))
`ch5_mid`	cv	CV that offsets channel 5's MID EQ band. control voltage (CV); modulates ch5_mid (summed directly (the destination DSP scales it))
`ch5_high`	cv	CV that offsets channel 5's HIGH EQ band. control voltage (CV); modulates ch5_high (summed directly (the destination DSP scales it))
`ch5_thresh`	cv	CV that offsets channel 5's compressor THRESHOLD. control voltage (CV); modulates ch5_thresh (summed directly (the destination DSP scales it))
`ch5_ratio`	cv	CV that offsets channel 5's compressor RATIO. control voltage (CV); modulates ch5_ratio (summed directly (the destination DSP scales it))
`ch5_compEnable`	cv	CV (discrete) that toggles channel 5's compressor ENABLE. control voltage (CV); modulates ch5_compEnable (summed directly (the destination DSP scales it))
`comp5`	cv	CV that offsets channel 5's COMP macro amount. control voltage (CV); modulates comp5 (summed directly (the destination DSP scales it))
`ch5_send1`	cv	CV that offsets channel 5's SEND 1 amount. control voltage (CV); modulates ch5_send1 (summed directly (the destination DSP scales it))
`ch5_send2`	cv	CV that offsets channel 5's SEND 2 amount. control voltage (CV); modulates ch5_send2 (summed directly (the destination DSP scales it))
`ch6_volume`	cv	CV that offsets channel 6's VOLUME fader (±1 CV sweeps the full 0..1 span around the knob). control voltage (CV); modulates ch6_volume (summed directly (the destination DSP scales it))
`ch6_low`	cv	CV that offsets channel 6's LOW EQ band. control voltage (CV); modulates ch6_low (summed directly (the destination DSP scales it))
`ch6_mid`	cv	CV that offsets channel 6's MID EQ band. control voltage (CV); modulates ch6_mid (summed directly (the destination DSP scales it))
`ch6_high`	cv	CV that offsets channel 6's HIGH EQ band. control voltage (CV); modulates ch6_high (summed directly (the destination DSP scales it))
`ch6_thresh`	cv	CV that offsets channel 6's compressor THRESHOLD. control voltage (CV); modulates ch6_thresh (summed directly (the destination DSP scales it))
`ch6_ratio`	cv	CV that offsets channel 6's compressor RATIO. control voltage (CV); modulates ch6_ratio (summed directly (the destination DSP scales it))
`ch6_compEnable`	cv	CV (discrete) that toggles channel 6's compressor ENABLE. control voltage (CV); modulates ch6_compEnable (summed directly (the destination DSP scales it))
`comp6`	cv	CV that offsets channel 6's COMP macro amount. control voltage (CV); modulates comp6 (summed directly (the destination DSP scales it))
`ch6_send1`	cv	CV that offsets channel 6's SEND 1 amount. control voltage (CV); modulates ch6_send1 (summed directly (the destination DSP scales it))
`ch6_send2`	cv	CV that offsets channel 6's SEND 2 amount. control voltage (CV); modulates ch6_send2 (summed directly (the destination DSP scales it))
`ch7_volume`	cv	CV that offsets channel 7's VOLUME fader (±1 CV sweeps the full 0..1 span around the knob). control voltage (CV); modulates ch7_volume (summed directly (the destination DSP scales it))
`ch7_low`	cv	CV that offsets channel 7's LOW EQ band. control voltage (CV); modulates ch7_low (summed directly (the destination DSP scales it))
`ch7_mid`	cv	CV that offsets channel 7's MID EQ band. control voltage (CV); modulates ch7_mid (summed directly (the destination DSP scales it))
`ch7_high`	cv	CV that offsets channel 7's HIGH EQ band. control voltage (CV); modulates ch7_high (summed directly (the destination DSP scales it))
`ch7_thresh`	cv	CV that offsets channel 7's compressor THRESHOLD. control voltage (CV); modulates ch7_thresh (summed directly (the destination DSP scales it))
`ch7_ratio`	cv	CV that offsets channel 7's compressor RATIO. control voltage (CV); modulates ch7_ratio (summed directly (the destination DSP scales it))
`ch7_compEnable`	cv	CV (discrete) that toggles channel 7's compressor ENABLE. control voltage (CV); modulates ch7_compEnable (summed directly (the destination DSP scales it))
`comp7`	cv	CV that offsets channel 7's COMP macro amount. control voltage (CV); modulates comp7 (summed directly (the destination DSP scales it))
`ch7_send1`	cv	CV that offsets channel 7's SEND 1 amount. control voltage (CV); modulates ch7_send1 (summed directly (the destination DSP scales it))
`ch7_send2`	cv	CV that offsets channel 7's SEND 2 amount. control voltage (CV); modulates ch7_send2 (summed directly (the destination DSP scales it))
`ch8_volume`	cv	CV that offsets channel 8's VOLUME fader (±1 CV sweeps the full 0..1 span around the knob). control voltage (CV); modulates ch8_volume (summed directly (the destination DSP scales it))
`ch8_low`	cv	CV that offsets channel 8's LOW EQ band. control voltage (CV); modulates ch8_low (summed directly (the destination DSP scales it))
`ch8_mid`	cv	CV that offsets channel 8's MID EQ band. control voltage (CV); modulates ch8_mid (summed directly (the destination DSP scales it))
`ch8_high`	cv	CV that offsets channel 8's HIGH EQ band. control voltage (CV); modulates ch8_high (summed directly (the destination DSP scales it))
`ch8_thresh`	cv	CV that offsets channel 8's compressor THRESHOLD. control voltage (CV); modulates ch8_thresh (summed directly (the destination DSP scales it))
`ch8_ratio`	cv	CV that offsets channel 8's compressor RATIO. control voltage (CV); modulates ch8_ratio (summed directly (the destination DSP scales it))
`ch8_compEnable`	cv	CV (discrete) that toggles channel 8's compressor ENABLE. control voltage (CV); modulates ch8_compEnable (summed directly (the destination DSP scales it))
`comp8`	cv	CV that offsets channel 8's COMP macro amount. control voltage (CV); modulates comp8 (summed directly (the destination DSP scales it))
`ch8_send1`	cv	CV that offsets channel 8's SEND 1 amount. control voltage (CV); modulates ch8_send1 (summed directly (the destination DSP scales it))
`ch8_send2`	cv	CV that offsets channel 8's SEND 2 amount. control voltage (CV); modulates ch8_send2 (summed directly (the destination DSP scales it))
`master_volume`	cv	CV that offsets the MASTER volume — modulate the overall output level of the whole mix. control voltage (CV); modulates master_volume (summed directly (the destination DSP scales it))
`send1Pre`	cv	CV (discrete) that switches the SEND 1 bus between POST-fader (low) and PRE-fader (high). control voltage (CV); modulates send1Pre (summed directly (the destination DSP scales it))
`send2Pre`	cv	CV (discrete) that switches the SEND 2 bus between POST-fader (low) and PRE-fader (high). control voltage (CV); modulates send2Pre (summed directly (the destination DSP scales it))
`ret1_volume`	cv	CV that offsets RETURN 1's level. control voltage (CV); modulates ret1_volume (summed directly (the destination DSP scales it))
`ret1_low`	cv	CV that offsets RETURN 1's LOW EQ band. control voltage (CV); modulates ret1_low (summed directly (the destination DSP scales it))
`ret1_mid`	cv	CV that offsets RETURN 1's MID EQ band. control voltage (CV); modulates ret1_mid (summed directly (the destination DSP scales it))
`ret1_high`	cv	CV that offsets RETURN 1's HIGH EQ band. control voltage (CV); modulates ret1_high (summed directly (the destination DSP scales it))
`ret2_volume`	cv	CV that offsets RETURN 2's level. control voltage (CV); modulates ret2_volume (summed directly (the destination DSP scales it))
`ret2_low`	cv	CV that offsets RETURN 2's LOW EQ band. control voltage (CV); modulates ret2_low (summed directly (the destination DSP scales it))
`ret2_mid`	cv	CV that offsets RETURN 2's MID EQ band. control voltage (CV); modulates ret2_mid (summed directly (the destination DSP scales it))
`ret2_high`	cv	CV that offsets RETURN 2's HIGH EQ band. control voltage (CV); modulates ret2_high (summed directly (the destination DSP scales it))

outputs

id	cable	what it does
`masterL`	audio	MASTER bus left output — all eight channels (post EQ/comp/fader) plus the two aux returns, summed. The main stereo mix out. audio signal
`masterR`	audio	MASTER bus right output, the partner of masterL. audio signal
`send1L`	audio	AUX SEND 1 left output — the sum of every channel scaled by its SEND 1 amount. Patch it into an external effect, then return the wet to ret1L/R. The tap point follows the send1Pre switch: POST-fader by default, or PRE-fader (before the volume fader) so the bus keeps carrying a muted channel. audio signal
`send1R`	audio	AUX SEND 1 right output, the partner of send1L. audio signal
`send2L`	audio	AUX SEND 2 left output — the sum of every channel scaled by its SEND 2 amount. Return its wet to ret2L/R. audio signal
`send2R`	audio	AUX SEND 2 right output, the partner of send2L. audio signal

params

id	label	range	default	curve
`ch1_volume`	1V	0..1	0.8	linear
`ch1_low`	1Lo	-12..12dB	0	linear
`ch1_mid`	1Md	-12..12dB	0	linear
`ch1_high`	1Hi	-12..12dB	0	linear
`ch1_thresh`	1Th	-36..0dB	-12	linear
`ch1_ratio`	1Rt	1..10	2	linear
`ch1_compEnable`	1Cp	0..1	0	discrete
`comp1`	1Cm	0..1	0	linear
`ch1_send1`	1S1	0..1	0	linear
`ch1_send2`	1S2	0..1	0	linear
`ch2_volume`	2V	0..1	0.8	linear
`ch2_low`	2Lo	-12..12dB	0	linear
`ch2_mid`	2Md	-12..12dB	0	linear
`ch2_high`	2Hi	-12..12dB	0	linear
`ch2_thresh`	2Th	-36..0dB	-12	linear
`ch2_ratio`	2Rt	1..10	2	linear
`ch2_compEnable`	2Cp	0..1	0	discrete
`comp2`	2Cm	0..1	0	linear
`ch2_send1`	2S1	0..1	0	linear
`ch2_send2`	2S2	0..1	0	linear
`ch3_volume`	3V	0..1	0.8	linear
`ch3_low`	3Lo	-12..12dB	0	linear
`ch3_mid`	3Md	-12..12dB	0	linear
`ch3_high`	3Hi	-12..12dB	0	linear
`ch3_thresh`	3Th	-36..0dB	-12	linear
`ch3_ratio`	3Rt	1..10	2	linear
`ch3_compEnable`	3Cp	0..1	0	discrete
`comp3`	3Cm	0..1	0	linear
`ch3_send1`	3S1	0..1	0	linear
`ch3_send2`	3S2	0..1	0	linear
`ch4_volume`	4V	0..1	0.8	linear
`ch4_low`	4Lo	-12..12dB	0	linear
`ch4_mid`	4Md	-12..12dB	0	linear
`ch4_high`	4Hi	-12..12dB	0	linear
`ch4_thresh`	4Th	-36..0dB	-12	linear
`ch4_ratio`	4Rt	1..10	2	linear
`ch4_compEnable`	4Cp	0..1	0	discrete
`comp4`	4Cm	0..1	0	linear
`ch4_send1`	4S1	0..1	0	linear
`ch4_send2`	4S2	0..1	0	linear
`ch5_volume`	5V	0..1	0.8	linear
`ch5_low`	5Lo	-12..12dB	0	linear
`ch5_mid`	5Md	-12..12dB	0	linear
`ch5_high`	5Hi	-12..12dB	0	linear
`ch5_thresh`	5Th	-36..0dB	-12	linear
`ch5_ratio`	5Rt	1..10	2	linear
`ch5_compEnable`	5Cp	0..1	0	discrete
`comp5`	5Cm	0..1	0	linear
`ch5_send1`	5S1	0..1	0	linear
`ch5_send2`	5S2	0..1	0	linear
`ch6_volume`	6V	0..1	0.8	linear
`ch6_low`	6Lo	-12..12dB	0	linear
`ch6_mid`	6Md	-12..12dB	0	linear
`ch6_high`	6Hi	-12..12dB	0	linear
`ch6_thresh`	6Th	-36..0dB	-12	linear
`ch6_ratio`	6Rt	1..10	2	linear
`ch6_compEnable`	6Cp	0..1	0	discrete
`comp6`	6Cm	0..1	0	linear
`ch6_send1`	6S1	0..1	0	linear
`ch6_send2`	6S2	0..1	0	linear
`ch7_volume`	7V	0..1	0.8	linear
`ch7_low`	7Lo	-12..12dB	0	linear
`ch7_mid`	7Md	-12..12dB	0	linear
`ch7_high`	7Hi	-12..12dB	0	linear
`ch7_thresh`	7Th	-36..0dB	-12	linear
`ch7_ratio`	7Rt	1..10	2	linear
`ch7_compEnable`	7Cp	0..1	0	discrete
`comp7`	7Cm	0..1	0	linear
`ch7_send1`	7S1	0..1	0	linear
`ch7_send2`	7S2	0..1	0	linear
`ch8_volume`	8V	0..1	0.8	linear
`ch8_low`	8Lo	-12..12dB	0	linear
`ch8_mid`	8Md	-12..12dB	0	linear
`ch8_high`	8Hi	-12..12dB	0	linear
`ch8_thresh`	8Th	-36..0dB	-12	linear
`ch8_ratio`	8Rt	1..10	2	linear
`ch8_compEnable`	8Cp	0..1	0	discrete
`comp8`	8Cm	0..1	0	linear
`ch8_send1`	8S1	0..1	0	linear
`ch8_send2`	8S2	0..1	0	linear
`master_volume`	Master	0..1	0.8	linear
`send1Pre`	S1Pre	0..1	0	discrete
`send2Pre`	S2Pre	0..1	0	discrete
`ret1_volume`	R1V	0..1	1	linear
`ret1_low`	R1Lo	-12..12dB	0	linear
`ret1_mid`	R1Md	-12..12dB	0	linear
`ret1_high`	R1Hi	-12..12dB	0	linear
`ret2_volume`	R2V	0..1	1	linear
`ret2_low`	R2Lo	-12..12dB	0	linear
`ret2_mid`	R2Md	-12..12dB	0	linear
`ret2_high`	R2Hi	-12..12dB	0	linear

controls

control	what it does
1Cp	Channel 1 compressor ENABLE (on/off) — bypasses or engages channel 1's compressor directly (the manual control under the COMP macro). CV via the ch1_compEnable input.
1Hi	Channel 1 HIGH EQ band (±12 dB) — boost/cut the highs on channel 1. CV via the ch1_high input.
1Lo	Channel 1 LOW EQ band (±12 dB) — boost/cut the lows on channel 1. CV via the ch1_low input.
1Md	Channel 1 MID EQ band (±12 dB) — boost/cut the mids on channel 1. CV via the ch1_mid input.
1Rt	Channel 1 compressor RATIO (1..10) — how hard channel 1's compressor reduces gain above the threshold (1 = none, 10 = strong). CV via the ch1_ratio input.
1S1	Channel 1 SEND 1 amount (0..1) — how much of channel 1 is tapped to aux-send bus 1 (the send1L/R outputs, e.g. for an external reverb). CV via the ch1_send1 input.
1S2	Channel 1 SEND 2 amount (0..1) — how much of channel 1 feeds aux-send bus 2. CV via the ch1_send2 input.
1Th	Channel 1 compressor THRESHOLD (−36..0 dB) — the level above which channel 1's compressor starts gain-reduction (only when COMP ENABLE / the COMP macro is on). CV via the ch1_thresh input.
1V	Channel 1 VOLUME fader (0..1) — the channel's level into the master bus + aux sends. CV via the ch1_volume input.
2Cp	Channel 2 compressor ENABLE (on/off) — bypasses or engages channel 2's compressor directly (the manual control under the COMP macro). CV via the ch2_compEnable input.
2Hi	Channel 2 HIGH EQ band (±12 dB) — boost/cut the highs on channel 2. CV via the ch2_high input.
2Lo	Channel 2 LOW EQ band (±12 dB) — boost/cut the lows on channel 2. CV via the ch2_low input.
2Md	Channel 2 MID EQ band (±12 dB) — boost/cut the mids on channel 2. CV via the ch2_mid input.
2Rt	Channel 2 compressor RATIO (1..10) — how hard channel 2's compressor reduces gain above the threshold (1 = none, 10 = strong). CV via the ch2_ratio input.
2S1	Channel 2 SEND 1 amount (0..1) — how much of channel 2 is tapped to aux-send bus 1 (the send1L/R outputs, e.g. for an external reverb). CV via the ch2_send1 input.
2S2	Channel 2 SEND 2 amount (0..1) — how much of channel 2 feeds aux-send bus 2. CV via the ch2_send2 input.
2Th	Channel 2 compressor THRESHOLD (−36..0 dB) — the level above which channel 2's compressor starts gain-reduction (only when COMP ENABLE / the COMP macro is on). CV via the ch2_thresh input.
2V	Channel 2 VOLUME fader (0..1) — the channel's level into the master bus + aux sends. CV via the ch2_volume input.
3Cp	Channel 3 compressor ENABLE (on/off) — bypasses or engages channel 3's compressor directly (the manual control under the COMP macro). CV via the ch3_compEnable input.
3Hi	Channel 3 HIGH EQ band (±12 dB) — boost/cut the highs on channel 3. CV via the ch3_high input.
3Lo	Channel 3 LOW EQ band (±12 dB) — boost/cut the lows on channel 3. CV via the ch3_low input.
3Md	Channel 3 MID EQ band (±12 dB) — boost/cut the mids on channel 3. CV via the ch3_mid input.
3Rt	Channel 3 compressor RATIO (1..10) — how hard channel 3's compressor reduces gain above the threshold (1 = none, 10 = strong). CV via the ch3_ratio input.
3S1	Channel 3 SEND 1 amount (0..1) — how much of channel 3 is tapped to aux-send bus 1 (the send1L/R outputs, e.g. for an external reverb). CV via the ch3_send1 input.
3S2	Channel 3 SEND 2 amount (0..1) — how much of channel 3 feeds aux-send bus 2. CV via the ch3_send2 input.
3Th	Channel 3 compressor THRESHOLD (−36..0 dB) — the level above which channel 3's compressor starts gain-reduction (only when COMP ENABLE / the COMP macro is on). CV via the ch3_thresh input.
3V	Channel 3 VOLUME fader (0..1) — the channel's level into the master bus + aux sends. CV via the ch3_volume input.
4Cp	Channel 4 compressor ENABLE (on/off) — bypasses or engages channel 4's compressor directly (the manual control under the COMP macro). CV via the ch4_compEnable input.
4Hi	Channel 4 HIGH EQ band (±12 dB) — boost/cut the highs on channel 4. CV via the ch4_high input.
4Lo	Channel 4 LOW EQ band (±12 dB) — boost/cut the lows on channel 4. CV via the ch4_low input.
4Md	Channel 4 MID EQ band (±12 dB) — boost/cut the mids on channel 4. CV via the ch4_mid input.
4Rt	Channel 4 compressor RATIO (1..10) — how hard channel 4's compressor reduces gain above the threshold (1 = none, 10 = strong). CV via the ch4_ratio input.
4S1	Channel 4 SEND 1 amount (0..1) — how much of channel 4 is tapped to aux-send bus 1 (the send1L/R outputs, e.g. for an external reverb). CV via the ch4_send1 input.
4S2	Channel 4 SEND 2 amount (0..1) — how much of channel 4 feeds aux-send bus 2. CV via the ch4_send2 input.
4Th	Channel 4 compressor THRESHOLD (−36..0 dB) — the level above which channel 4's compressor starts gain-reduction (only when COMP ENABLE / the COMP macro is on). CV via the ch4_thresh input.
4V	Channel 4 VOLUME fader (0..1) — the channel's level into the master bus + aux sends. CV via the ch4_volume input.
5Cp	Channel 5 compressor ENABLE (on/off) — bypasses or engages channel 5's compressor directly (the manual control under the COMP macro). CV via the ch5_compEnable input.
5Hi	Channel 5 HIGH EQ band (±12 dB) — boost/cut the highs on channel 5. CV via the ch5_high input.
5Lo	Channel 5 LOW EQ band (±12 dB) — boost/cut the lows on channel 5. CV via the ch5_low input.
5Md	Channel 5 MID EQ band (±12 dB) — boost/cut the mids on channel 5. CV via the ch5_mid input.
5Rt	Channel 5 compressor RATIO (1..10) — how hard channel 5's compressor reduces gain above the threshold (1 = none, 10 = strong). CV via the ch5_ratio input.
5S1	Channel 5 SEND 1 amount (0..1) — how much of channel 5 is tapped to aux-send bus 1 (the send1L/R outputs, e.g. for an external reverb). CV via the ch5_send1 input.
5S2	Channel 5 SEND 2 amount (0..1) — how much of channel 5 feeds aux-send bus 2. CV via the ch5_send2 input.
5Th	Channel 5 compressor THRESHOLD (−36..0 dB) — the level above which channel 5's compressor starts gain-reduction (only when COMP ENABLE / the COMP macro is on). CV via the ch5_thresh input.
5V	Channel 5 VOLUME fader (0..1) — the channel's level into the master bus + aux sends. CV via the ch5_volume input.
6Cp	Channel 6 compressor ENABLE (on/off) — bypasses or engages channel 6's compressor directly (the manual control under the COMP macro). CV via the ch6_compEnable input.
6Hi	Channel 6 HIGH EQ band (±12 dB) — boost/cut the highs on channel 6. CV via the ch6_high input.
6Lo	Channel 6 LOW EQ band (±12 dB) — boost/cut the lows on channel 6. CV via the ch6_low input.
6Md	Channel 6 MID EQ band (±12 dB) — boost/cut the mids on channel 6. CV via the ch6_mid input.
6Rt	Channel 6 compressor RATIO (1..10) — how hard channel 6's compressor reduces gain above the threshold (1 = none, 10 = strong). CV via the ch6_ratio input.
6S1	Channel 6 SEND 1 amount (0..1) — how much of channel 6 is tapped to aux-send bus 1 (the send1L/R outputs, e.g. for an external reverb). CV via the ch6_send1 input.
6S2	Channel 6 SEND 2 amount (0..1) — how much of channel 6 feeds aux-send bus 2. CV via the ch6_send2 input.
6Th	Channel 6 compressor THRESHOLD (−36..0 dB) — the level above which channel 6's compressor starts gain-reduction (only when COMP ENABLE / the COMP macro is on). CV via the ch6_thresh input.
6V	Channel 6 VOLUME fader (0..1) — the channel's level into the master bus + aux sends. CV via the ch6_volume input.
7Cp	Channel 7 compressor ENABLE (on/off) — bypasses or engages channel 7's compressor directly (the manual control under the COMP macro). CV via the ch7_compEnable input.
7Hi	Channel 7 HIGH EQ band (±12 dB) — boost/cut the highs on channel 7. CV via the ch7_high input.
7Lo	Channel 7 LOW EQ band (±12 dB) — boost/cut the lows on channel 7. CV via the ch7_low input.
7Md	Channel 7 MID EQ band (±12 dB) — boost/cut the mids on channel 7. CV via the ch7_mid input.
7Rt	Channel 7 compressor RATIO (1..10) — how hard channel 7's compressor reduces gain above the threshold (1 = none, 10 = strong). CV via the ch7_ratio input.
7S1	Channel 7 SEND 1 amount (0..1) — how much of channel 7 is tapped to aux-send bus 1 (the send1L/R outputs, e.g. for an external reverb). CV via the ch7_send1 input.
7S2	Channel 7 SEND 2 amount (0..1) — how much of channel 7 feeds aux-send bus 2. CV via the ch7_send2 input.
7Th	Channel 7 compressor THRESHOLD (−36..0 dB) — the level above which channel 7's compressor starts gain-reduction (only when COMP ENABLE / the COMP macro is on). CV via the ch7_thresh input.
7V	Channel 7 VOLUME fader (0..1) — the channel's level into the master bus + aux sends. CV via the ch7_volume input.
8Cp	Channel 8 compressor ENABLE (on/off) — bypasses or engages channel 8's compressor directly (the manual control under the COMP macro). CV via the ch8_compEnable input.
8Hi	Channel 8 HIGH EQ band (±12 dB) — boost/cut the highs on channel 8. CV via the ch8_high input.
8Lo	Channel 8 LOW EQ band (±12 dB) — boost/cut the lows on channel 8. CV via the ch8_low input.
8Md	Channel 8 MID EQ band (±12 dB) — boost/cut the mids on channel 8. CV via the ch8_mid input.
8Rt	Channel 8 compressor RATIO (1..10) — how hard channel 8's compressor reduces gain above the threshold (1 = none, 10 = strong). CV via the ch8_ratio input.
8S1	Channel 8 SEND 1 amount (0..1) — how much of channel 8 is tapped to aux-send bus 1 (the send1L/R outputs, e.g. for an external reverb). CV via the ch8_send1 input.
8S2	Channel 8 SEND 2 amount (0..1) — how much of channel 8 feeds aux-send bus 2. CV via the ch8_send2 input.
8Th	Channel 8 compressor THRESHOLD (−36..0 dB) — the level above which channel 8's compressor starts gain-reduction (only when COMP ENABLE / the COMP macro is on). CV via the ch8_thresh input.
8V	Channel 8 VOLUME fader (0..1) — the channel's level into the master bus + aux sends. CV via the ch8_volume input.
1Cm	Channel 1 COMP macro (0..1) — one knob that collapses the per-channel compressor: 0 = bypass, and (0,1] enables it while interpolating the threshold from 0 dB down to −20 dB and the ratio from 1:1 up to 4:1, for a quick "isolate this channel" amount. Overrides the manual thresh/ratio/enable when moved. CV via the comp1 input.
2Cm	Channel 2 COMP macro (0..1) — one knob that collapses the per-channel compressor: 0 = bypass, and (0,1] enables it while interpolating the threshold from 0 dB down to −20 dB and the ratio from 1:1 up to 4:1, for a quick "isolate this channel" amount. Overrides the manual thresh/ratio/enable when moved. CV via the comp2 input.
3Cm	Channel 3 COMP macro (0..1) — one knob that collapses the per-channel compressor: 0 = bypass, and (0,1] enables it while interpolating the threshold from 0 dB down to −20 dB and the ratio from 1:1 up to 4:1, for a quick "isolate this channel" amount. Overrides the manual thresh/ratio/enable when moved. CV via the comp3 input.
4Cm	Channel 4 COMP macro (0..1) — one knob that collapses the per-channel compressor: 0 = bypass, and (0,1] enables it while interpolating the threshold from 0 dB down to −20 dB and the ratio from 1:1 up to 4:1, for a quick "isolate this channel" amount. Overrides the manual thresh/ratio/enable when moved. CV via the comp4 input.
5Cm	Channel 5 COMP macro (0..1) — one knob that collapses the per-channel compressor: 0 = bypass, and (0,1] enables it while interpolating the threshold from 0 dB down to −20 dB and the ratio from 1:1 up to 4:1, for a quick "isolate this channel" amount. Overrides the manual thresh/ratio/enable when moved. CV via the comp5 input.
6Cm	Channel 6 COMP macro (0..1) — one knob that collapses the per-channel compressor: 0 = bypass, and (0,1] enables it while interpolating the threshold from 0 dB down to −20 dB and the ratio from 1:1 up to 4:1, for a quick "isolate this channel" amount. Overrides the manual thresh/ratio/enable when moved. CV via the comp6 input.
7Cm	Channel 7 COMP macro (0..1) — one knob that collapses the per-channel compressor: 0 = bypass, and (0,1] enables it while interpolating the threshold from 0 dB down to −20 dB and the ratio from 1:1 up to 4:1, for a quick "isolate this channel" amount. Overrides the manual thresh/ratio/enable when moved. CV via the comp7 input.
8Cm	Channel 8 COMP macro (0..1) — one knob that collapses the per-channel compressor: 0 = bypass, and (0,1] enables it while interpolating the threshold from 0 dB down to −20 dB and the ratio from 1:1 up to 4:1, for a quick "isolate this channel" amount. Overrides the manual thresh/ratio/enable when moved. CV via the comp8 input.
Master	MASTER output level (0..1) — the overall gain of the whole mix bus. CV via the master_volume input.
R1Hi	RETURN 1 HIGH EQ band (±12 dB). CV via the ret1_high input.
R1Lo	RETURN 1 LOW EQ band (±12 dB) — shape the returning wet signal (e.g. roll the lows out of a reverb). Bypassed entirely while all three return-1 bands sit at 0 dB. CV via the ret1_low input.
R1Md	RETURN 1 MID EQ band (±12 dB). CV via the ret1_mid input.
R1V	RETURN 1 level (0..1, default 1 = unity) — how loud the wet signal coming back from the effect on send 1 sits in the master. This is the knob that makes a PRE-fader send usable: with send 1 switched to PRE, the return keeps sounding while the source channel is muted, and this sets how loud. CV via the ret1_volume input.
R2Hi	RETURN 2 HIGH EQ band (±12 dB). CV via the ret2_high input.
R2Lo	RETURN 2 LOW EQ band (±12 dB) — shape the returning wet signal (e.g. roll the lows out of a reverb). Bypassed entirely while all three return-2 bands sit at 0 dB. CV via the ret2_low input.
R2Md	RETURN 2 MID EQ band (±12 dB). CV via the ret2_mid input.
R2V	RETURN 2 level (0..1, default 1 = unity) — how loud the wet signal coming back from the effect on send 2 sits in the master. This is the knob that makes a PRE-fader send usable: with send 2 switched to PRE, the return keeps sounding while the source channel is muted, and this sets how loud. CV via the ret2_volume input.
S1Pre	SEND 1 PRE/POST-fader switch. POST (the default) taps each channel AFTER its volume fader, so pulling a fader down takes its send with it. PRE taps after EQ + compressor but BEFORE the fader, so the send level is the channel's signal × its SEND 1 amount no matter where the fader sits — which is how a RETURN keeps carrying sound while the channel it sits on is muted (a monitor feed, or a reverb that should ring on through a mute). Affects the whole send-1 bus, and is independent of SEND 2's switch.
S2Pre	SEND 2 PRE/POST-fader switch — the same choice as send1Pre, for the send-2 bus, and set independently of it: send 1 can be PRE while send 2 stays POST.

source

mixmstrs.ts on GitHub.